TL;DR: We come to you across Perth, fit the right gear with tidy wiring, test it and show you how to use it. You get a clean, reliable setup and friendly support if you ever need a hand.
Key Takeaways:
- Mobile supply and install across NOR, SOR and the CBD, plus dealerships, fleets and mine sites.
- Clear quotes before work starts, simple scheduling and an on time arrival.
- Careful wiring and integration for audio, cameras, comms and marine gear.
- Most jobs finish in one visit, with straightforward warranty and aftercar
You want a smooth install that fits your day and leaves your vehicle tidy and better to drive, and that is how we run every job. One of our installers arrives on time at your home, workplace, dealership or approved site with the right parts and tools, then we say hello, confirm the plan and set up without fuss.
If you are new to us, you can learn more about Mobile Audio Engineering. From hello to handover, we keep you in the loop, work carefully and leave everything looking factory neat.
Service Area and Arrival
We are based in central Perth and travel across the north, south and the CBD. We also look after dealerships, fleets and approved mine sites when the job needs to happen on location.
On the day, we send a quick text or call with an ETA so you can plan around school runs or meetings. Please check parking height limits, secure garages, gate codes or marina access if we are working at a boat or depot, and for a deeper look at our story and approach.
Step-by-Step: The Install Day Flow
The sequence is consistent so you always know what is happening. If your job includes audio upgrades, cameras, or comms, we follow the same careful rhythm.

Arrival and Walk‑Through
We start by confirming the plan with you, then take a quick look over the vehicle. We note mounting points and safe wiring paths and answer any last questions. If the job includes a head unit, we check factory features like steering wheel controls and cameras so we can confirm they work as expected at the end.
Protection First
Seat covers go on and drop sheets protect trims, and we use proper trim tools to avoid marks. When needed, we disconnect the battery, work safely around airbags and sensors, and run a quick check before we start fitting parts.
Fit and Wire
We mount the gear, route cables along safe paths, set fusing close to the power source and make solid earths. For marine jobs we add sealing and tinned wire as needed so you get clean power, a clear signal and a secure fit that looks the part.
Integration Checks
We test steering wheel controls, Bluetooth, Apple CarPlay or Android Auto, microphones and cameras to make sure everything works as it should. For dash cams, we set the time and date, select a sensible resolution and parking mode, and match button lighting to the factory settings.
Tidy‑up and Sign‑off
We refit panels, vacuum the cabin, and remove any packaging. Old parts can be left with you or taken away for recycling if requested. We then give you a short demo and make sure you are happy.
For a detailed look at one of our core services, see our Car Audio Installation Perth page.
Timing Guide: How Long it Usually Takes
Here is a simple guide to timing:
- Head unit: often a few hours, depending on the vehicle.
- Full system with speakers, amplifier and sub: takes longer; we allow extra time for tuning and checks.
- Dash cam: varies by model and cable routing; front and rear takes longer than front only.
- Extras and complexity: tricky trims, CANBUS work or extra accessories can add time.
We plan the day so most jobs finish neatly in a single visit.
Quality, Safety, and Compliance
Good wiring keeps your gear stable and safe, with the right cable size, a fuse near the power source and solid earths. We also route looms away from airbags and moving parts, and use no‑cut harnesses and integration modules to keep factory features working.
On the water we use tinned wire, proper sealing and hardware that stands up to salt and heat. For mine‑spec jobs we can add radios, lighting, tags and the right documentation so everything runs reliably without surprises.
Handover and Setup
Once the gear is in and tested, we set up your phone and show you how to use it. We help pair devices, choose CarPlay or Android Auto, and set a clean base EQ.
If you have an amplifier, we explain gains in plain terms so you can enjoy clear sound without distortion. For dash cams, we show how to find and save footage and how to care for the memory card. We leave you with tips that keep everything running well.
Aftercare, Warranty, and Support
We stand behind the gear we supply and install. If you hear a rattle or want a small tweak, reach out and we will book a time to check it.
Warranty support is simple because we know the parts, the wiring and the install history. If you change vehicles later, we can move your gear across so everything keeps working the way it should.
Why Choose Mobile Audio Engineering
You want work done right the first time. We are car audio specialists in perth who come to you, which saves you time and hassle.
Our vans carry the right parts and tools so we can solve problems on site. We work on cars, 4WDs, boats, caravans, trucks, buses, and plant equipment.
We care about neat cabling, solid mounts, and gear that suits your needs, not just the badge on the box.

Ready to book?
Ready when you are. Tell us your vehicle and what you want to achieve, and we’ll set up a time that suits.




